50 POP false wall design ideas for modern homes catalogue 2019

Installation of a false wall or gypsum board wall helps in many cases - if it is worthwhile to hide the lines of communications if there is to be an additional over the main wall if it is necessary to hide radiators, pipes. In this work there is nothing super complicated, a non-professional can do it too. However, some experience of repair work is still required, as well as special equipment.

In this subject, we are going to tell you how to install gypsum wall decoration and pop wall design step by step with a great gallery of photos contain the latest false wall designs. Go!

Don't miss: Latest POP design for hall false ceiling and walls

Latest gypsum board wall designs for hall and living room 2019 catalogue

Why do we need a POP false wall design?

First, it is sound insulation or wall insulation. It turns out that behind the false wall you hide the insulation material or soundproofing. Usually, we are talking about mineral wool.

False wall and installation reasons:

Laying the system of hidden communications;
Installation of hidden mechanisms;
Decorative purposes - for example, the construction of special niches.

Finally, such a false wall can even out the curvatures of the base wall. Well, of course, this is a partition without the load-carrying capacity for the room - so that between the two zones in the room there was such a homemade wall. This zoning is also very in demand.

Preparatory stage: pop wall design of plasterboard

The preparatory stage includes the selection of materials and tools. Acquire the material of the manufacturer with a good reputation. Most often choose a moisture-resistant gypsum board, since the task of a false wall is to hide water pipes.

You will need tools:

Construction glasses;
Hacksaw for gypsum;
Level;
Pliers;
Shears for metal;
A hammer;
Side cutters;
Roulette with lock;
Knife with a replaceable blade.

The next stage is the marking of the walls for installation. Using a paint string, you can mark the ceiling and the floor. At the distance that is optimal for hiding the pipes, two lines parallel to one wall are beaten off the wall. One will go to the ceiling, the other on the floor. Interval of 10-15 cm is usually enough. Then at a distance of 600 mm from each other, vertical lines parallel to each other are beaten. It is for them to install fasteners.

Best false wall design ideas in living rooms

Installation of the battens: a false wall design of gypsum board wall with own hands

Next, you need to make a few holes. Here, a puncher will come to the rescue. The interval between the holes is 25 cm. The dowels are blocked in these holes.

Then the work goes like this:

After the holes are ready, they are screwed on the guides from the metal profile. These elements of the frame are needed as basic supports, and further installation of the crate is carried out.
Reiki from the metal profile is fixed at a distance of approximately 50-70 cm from each other, this is done using a U-shaped profile (it is mounted on the wall itself).
If all this is done in a wooden house, all the work is simplified, because you do not need to drill the surface and clog the dowels. The lining should be simply screwed with screws.

When working with the crate, clearly monitor the plane. You can use for this purpose both simple bubble level, and a high-grade water level. But there is nothing better than a laser level with this task. He guarantees maximum accuracy.

How to make a false wall design of gypsum board wall

When the crate is ready, you can begin the installation. Gypsum board wall sheets are measured and cut according to the parameters of the crate. To cut drywall, you can take and a simple clerical knife, one that cut the cardboard cover, well, and then simply break off the excess. The remaining layer of cardboard is cut, and a sheet can be screwed.

Gypsum board wall is applied to the frame of the crate, screwed with screws. Be extremely careful, because you work with a fragile material, and if you do not calculate the force of pressing the tool, the plate is easy to press.

After screwing the first layer of GCR, on top of it start mounting the second one. On top of the second sheet is mounted to strengthen the structure. When installing extreme sheets of gypsum board, it can be difficult - a normal plane will help, at an angle of 45 degrees; a chamfer is removed from the sheet.

New POP false ceiling designs 2019

Instruction: false wall design of plasterboard for sliding door

Popular sliding doors have become in recent years - they decorate the hall, they will be good in the children's room, they will fit in the design of the kitchen. How to insert sliding doors into a false wall or a drywall partition? Follow a specific, rather simple algorithm.

Installing doors in a false wall:

Calculate the height of the guide rail and the dimensions of the future doorway;
Next, the skeleton of the partition is mounted;
Then install the door guide and travel stops;
Next comes the lining of the carcass with gypsum boards, and then the flooring of the clean floor;
After that, you can safely hang the door leaf with the installation of platbands.

The frame is covered with plasterboard, flooring is applied. On the door leaf, the brackets are fastened to connect them to the pins of the rollers, the groove for the lower guide is selected.

The great popularity of false walls is due to the ease of installation, availability of material, and a range of possibilities. No easier than to take the environmentally friendly material, cheap, time-tested, and strictly in technology to make a false wall from it. With this will cope and not a professional.